BULLETIN NO. 1600

AIR CLEANING SYSTEMS AND
EQUPMENT BY
R. M.E. I., INC.

FILTER-MATE IS THE SOLUTION TO YOUR CLEAN AIR REQUIREMENTS


THE COMPETITIVE EDGE -- FILTER MATE HAS IT ALL
 
  • Side loaded housing accespts more filter combinations. Up to five stages of progressive density filtration available for maximum efficiency. Filter choices include panel prefilters, mist cellectors, spark arrestors, extended surface pleats, V-bags, HEPAS, partial bypass or solid bed panels of activated charcoal.
  • A wide variety of motor and blower sizes are available to better meet user's requirements.
  • The ability for you to select a filter-motor-blower combination provides for unlimited versatility.
  • Cabinet designed to end load or side load for more applications.
  • Our technical and engineering support helps you select the correct unit for your application.


  • APPLICATIONS
    The FM-50 can be used with or without ductwork to move up to 2000 cfm. Thse units remove tobacco smoke as well as the other 1000 identified indoor air pollutants of which at least 60 are carcinogenic. These contaminants are removed in commercial applications such as computer rooms, lounges, breakrooms, restaurants, kitchens, etc. In Industrial applications these units remove weld fumes, oil smoke, lint, dust, oil mist, odors, gases, paint overspray, etc. Units can be mounted horizontally or vertically to accept source capture hoods, source capture hoses, ductwork, additional filter modules, etc.
    Design & Construction
    The FM-50 is a self contained air cleaner with blower, motor, and 26" length filter compartment in one cabinet. Cabinetry is rugged 16 gauge galvanized steel with 1 1/2 inch flanges for ductwork interface. Acceptance of universal holding frames allow the use of pleated/rigid cells or V-bags with high sealing integrity. Holding clamps allow HEPA filters and charcoal modules to seal positively against an interal sealing flange. Prefilter tracks are available to accept 2" or 4" deep prefilters. Both belt drive and direct drive forward inclined blowers are available. Access door is 16 gauge galvanized steel with replaceable positive sealing latches and replaceable hinges. Access door, access panel, and filter compartment are gasketed for air tight seal.

    MODELS AND SPECIFICATIONS

    FM-50-LP FM-50-RG
    Low profile model accepts 12"x24" face dimension filters. Dimensions: 18.5" height x 24.0" width x 50.25" length. Weight: 145 lbs   Regular housing accepts 24"x24" face dimension filters. Dimensions: 27.25" height x 24.0" width x 50.25" length. Weight: 195 lbs
    MOTOR AND BLOWER COMBINATIONS CFM AT STATIC PRESSURE RPM   MOTOR AND BLOWER COMBINATIONS CFM AT STATIC PRESSURE RPM
    1/4 HP 3 speed 115 V.A.C.
    9"x7" direct drive blower
    800 cfm @ 0.80" S.P. 1075 rpm*   1/2 HP 3 speed 115 V.A.C.
    10"x10" direct drive blower
    1600 cfm @ 1.00" S.P. 1075 rpm*
    1/3 HP 3 speed 115 V.A.C.
    9"x9" direct drive blower
    1000 cfm @ 0.85" S.P. 1100 rpm*   3/4 HP 3 speed 115/ 230 V.A.C.
    10"x10" direct drive blower
    2000 cfm @ 0.90" S.P. 1075 rpm*
    1/2 HP 3 speed 115 V.A.C.
    9"x9" direct drive blower
    1200 cfm @ 0.80" S.P. 1100 rpm*   3/4 HP 3 speed 230 V.A.C.
    12"x9" direct drive blower
    1700 cfm @ 1.70" S.P. 1075 rpm*
    1/2 HP 3 speed 115 V.A.C.
    9"x9" direct drive blower
    1000 cfm @ 1.80" S.P. 1625 rpm*   1/2 HP 1 speed 115/230 V.A.C.
    10"x10" belt drive blower
    1600 cfm @ 0.70" S.P. 975 rpm*
    1/3 HP 1 speed 115 V.A.C.
    9"x7" belt drive blower
    800 cfm @ 0.70" S.P. 1100 rpm*   3/4 HP 1 speed 115/230 V.A.C.
    10"x10" belt drive blower
    2000 cfm @ 0.90 S.P. 1075 rpm*
    1/2 HP 1 speed 115/230 V.A.C.
    9"x9" belt drive blower
    1000 cfm @ 1.00" S.P. 1200 rpm*   1 HP 1 speed 208-230/460 3-phase V.A.C 2200 cfm @ 1.00" S.P. 1200 rpm*

    Filter-Combinations
    1. 2" prefilter + 12" pleated + 8 " charcoal
    2. 2" prefilter + 12" HEPA +8" charcoal
    3. 2" prefilter + 24" long bag filter
    4. 4" prefilter +12" Pleated or 12" HEPA

    NOTES:
    1. Holding frame is required for pleated/rigid filter
    2. Holding clamps are required for HEPA and charcoal filters.
    3. Holding frame is recommended but no required for bag filter. Bag filter can be side loaded or end loaded.
    4. Charcoal cells are available in 8" deep disposable partial bypass (up to 20 lb. maximum) or refillable solid bed (30 lb maximum).
    5. CFM can vary depending on filter combination used.